ttyI
ttyi(4) Special files ttyi(4)
NAME
ttyI - ISDN character devices with modem emulator
DESCRIPTION
ttyI[0-63] are emulated tty devices of the Linux ISDN subsystem. These
devices can be used in the same way as the traditional serial devices
ttySx. The official major device numbers are 43 for ttyI . The minor
device numbers start with 0 and end with 63.
The ISDN tty devices are equipped with a modem emulation implementing a
set of traditional and some special AT commands. This provides easy use
together with almost all communication software that uses modem com-
mands: minicom(1), seyon(1), XCept(1), uucico(8), mgetty(8), dip(8),
pppd(8) and more. When enabled during kernel configuration, the emula-
tor is capable of a reduced set of commands to support audio. To use
audio features, an ISDN card with a audio-capable low-level driver is
needed. Currently the only audio-capable drivers are the teles and
HiSax driver.
The line disciplines are handled by the kernel so that SLIP, CSLIP and
asynchronous PPP are possible.
The port speed of the ISDN tty devices is always 64000 bps.
AT COMMAND SET
The description of AT commands here does not cover audio related com-
mands. For a description of audio related commands, see isdn_audio(4).
The following AT commands are supported by ISDN tty devices:
ATA Answer an incoming call.
ATDnum Dial number num. Allowed are digits [0-9] and the characters
",", "#", ".", "*", "W", "P", "T", "S", "-". The characters are
ignored except of "S" which indicates a SPV if it precedes the
number (only German 1TR6 ISDN).
ATE0 Echo off.
ATE1 Echo on (default).
ATH Hang up.
ATH0 Hang up.
ATH1 Off hook (ignored).
ATI Return device Information ("ISDN for Linux...").
ATI0 Return device Information ("ISDN for Linux...").
ATI1 Return device Information ("ISDN for Linux...").
ATI2 Return Statistics of last connection.
ATO Return from command mode to online mode (data mode).
ATQ0 Enable result codes (default).
ATQ1 Disable result codes.
ATSx=y Set register x to value y.
ATSx? Show content of register x.
ATSx.y=z
Set register x, bit y to value z
ATSx.y?
Show bit y of register x.
ATV0 Print result code as number.
ATV1 Print result code as text (default).
ATZ Reset all registers and load profile values.
AT&Bx Set packet size of outgoing packets to value x (maximum 4000).
The actual packet size depends on the hardware driver and may be
smaller than x (e.g. with the teles driver). There will be no
error message if the value is bigger than the hardware driver
can process. However the size of the outgoing packets will be
set correctly.
AT&D2 DTR falling edge: hang up and return to command mode (default).
AT&D3 DTR falling edge: hang up, return to command mode and reset all
registers.
AT&Ex Set MSN (Euro-ISDN, EDSS1) or EAZ (German 1TR6) to value x. For
MSNs, x is a string of digits representing the local phone num-
ber, while for EAZs x should be only the last digit of the Num-
ber.
AT&F Set all registers and profile to "factory-defaults".
AT&Lplist
Set list of phone numbers to listen on. plist is a list of
wildcard patterns separated by semicolon. If this is set, it has
precedence over the MSN set by AT&E.
AT&V Show current register settings.
AT&W0 Write registers and EAZ/MSN to profile. (You need to run
iprofd(8) for making changes permanent.)
AT&X0 Disable BTX-Mode (default).
AT&X1 Enable BTX-Mode.
ESCAPE SEQUENCE
During a data connection, the driver can be set to command mode by typ-
ing in delay+++delay. The escape character (default "+") may be set
via register 2. The delay must be at least 1.5 seconds and between each
escape character the pause must not exceed 0.5 seconds. ATO brings the
modem emulation back to data mode.
REGISTERS
0 (default 0)
Number of rings on which the "modem" will answer. (S0=0 will
disable auto answering).
1 (default 0)
Counts and stores the number of rings from an incoming call.
2 (default 43 = '+')
ASCII code of the escape character.
3 (default 13 = CR)
ASCII code of Carriage Return.
4 (default 10 = LF)
ASCII code of Line Feed.
5 (default 8 = BS)
ASCII code of Backspace.
6 (default 3)
Duration, in number of seconds, modem waits before dialling.
7 (default 60)
Wait time for carrier in seconds.
8 (default 2)
Pause time for comma (',') in dial command in seconds (ignored).
9 (default 6)
Carrier detect time in tenths of seconds (ignored).
10 (default 7)
Wait time until hangup after carrier loss in tenths of seconds
(ignored).
11 (default 70)
Duration and delay in milliseconds for touch tone dialling
(ignored).
12 (default 69)
Bit-mapped register.
Bit Description
0 0 = Suppress response messages.
1 = Show response messages.
1 0 = Response messages as text.
1 = Numeric response messages.
2 0 = Echo off.
1 = Echo on.
3 0 = DCD always on.
1 = DCD follows carrier.
4 0 = CTS follows RTS.
1 = Ignore RTS, CTS always on.
5 0 = Low-edge on DTR: Hangup and return
to command mode.
1 = Same as 0 but also resets all
registers.
6 0 = DSR always on.
1 = DSR on only if channel is available.
7 0 = Cisco-PPP-flag-hack off.
1 = Cisco-PPP-flag-hack on.
13 (default 4)
Bit-mapped register.
Bit Description
0 0 = Use delayed sending of data.
1 = Immediately send data.
1 0 = T.70 protocol off.
1 = T.70 protocol on.
2 0 = Don't hangup on DTR low.
1 = Hangup on DTR low.
3 0 = Standard response messages.
1 = Extended response messages.
4 0 = CALLER NUMBER before every RING.
1 = CALLER NUMBER after first RING.
5 0 = Disable extended T.70 protocol.
1 = Enable extended T.70 protocol.
6 0 = Disable RUNG message.
1 = RUNG on cancelled incoming call.
7 0 = Disable display messages from net.
1 = Enable disable messages from net.
14 (default 0)
Layer-2 protocol.
0 = X75/LAPB with I-frames.
1 = X75/LAPB with UI-frames.
2 = X75/LAPB with BUI-frames.
3 = HDLC.
4 = TRANSPARENT.
10 = Analog Modem. (only if hardware supports this)
11 = Fax G3. (only if hardware supports this)
15 (default 0)
Layer-3 protocol.
0 = transparent
1 = transparent with audio features (e.g. DSP)
2 = Fax G3
16 (default 250)
Outgoing packet size / 16.
17 reserved.
18 (default 4)
Service-Octet-1 to accept or to be used on dial out.
Bit-mapped register.
Bit Description
0 Service 1 (audio) when set.
1 Service 5 (BTX) when set.
2 Service 7 (data) when set.
Note: It is possible to set more than one bit. In this case, on
outgoing calls, the most significant 1-bit is chosen to
select the outgoing service octet. On incoming calls the
selected services are accepted, contents of register 14
is ignored and the Layer-2-protocol is automatically set
with the following values to match the service of the
incoming call:
Incoming service audio (Reg. 20.0 = 1)
L2-protocol is set to 4 (TRANSPARENT).
Incoming service BTX (Reg. 20.1 = 1)
L2-protocol is set to 0 (X75/LAPB with I-frames).
Incoming service date (Reg. 20.2 = 1)
L2-protocol is set to 0 (X75/LAPB with I-frames).
19 (default 0)
Service-Octet-2 (ignored when using EDSS1).
20 (read only)
Service-Octet-1 of last incoming call. This bit-mapped register
is set on incoming call (during RING). Mapping is the same like
register 18.
21 (read only)
Bit-mapped register. Set on incoming call (during RING) to the
value of octet 3 of calling party number Information Element
(Numbering plan). See section 4.5.10 of ITU Q.931.
22 (read only)
Bit-mapped register. Set on incoming call (during RING) to the
value of octet 3a of calling party number Information Element
(Screening info). See section 4.5.10 of ITU Q.931.
23 (default 0)
Bit-mapped register.
Bit Description
0 0 = Disable CPN extended RING.
1 = Enable CPN extended RING.
1 0 = Disable CPN extended FCON.
1 = Enable CPN extended FCON.
NOTE There used also be cui devices (major device number 44), but
since the cua devices for regular tty devices are no longer sup-
ported in the kernel, these are also no longer supported for
ISDN4linux.
AUTHOR
Fritz Elfert <fritz@isdn4linux.de>
modified by Paul Slootman <paul@isdn4linux.de>
SEE ALSO
icnctrl(8), telesctrl(8), isdninfo(4), isdn_audio(4), isdnctrl(8).
ISDN 4 Linux 3.1pre4 2002/01/31 ttyi(4)
